{
 "measured_on": "2026-10-20",
 "question": "Which repairs make a generated model printable, and which make it worse?",
 "print_size_mm": 80,
 "source": "the 80 mm copies from gen-mesh-baseline-2026-10-15.json, oriented as a slicer receives them",
 "tools": {
  "blender": "5.2.2",
  "print3d_toolbox": "1.5.0 (extensions.blender.org)",
  "prusaslicer": "2.9.6",
  "trimesh": "5.1.0"
 },
 "deviation_method": "60000 points sampled on each surface; distance to the nearest sampled point on the other. \"removed\" = original to repaired, \"added\" = repaired to original. Two different samplings of the same surface are not identical, so the \"none\" row of each model gives the noise floor of this method; read the other rows against it.",
 "notes": [
  "The TRELLIS.2 charger as generated sliced to 0.98 m of filament in this run and to 0.50 m in gen-mesh-baseline-2026-10-15.json, from the same file and the same PrusaSlicer. With 401 open edges its inside is not defined, and the PrusaSlicer result on it was not repeatable. The other three TRELLIS.2 models gave the same figure in both runs.",
  "solidify_12 was first run with Even Thickness on. From the 80 mm models it produced bounding boxes of 871.5 x 893.8 x 3049.1 mm (TRELLIS.2 pumpkin) and 115.6 x 6064.8 x 95.8 mm (TRELLIS.2 charger): on two surfaces 0.16 mm apart, even thickness pushes vertices out by metres. Those files were replaced by the default run measured here and are not in this dataset.",
  "Repair before remesh (win_voxel_*) gave the same solid volume as remeshing the file as generated on every model, and shell counts within 11 of it. It differed in two cases: the Neural4D figurine at 1.0 mm came out watertight in one shell only when repaired first, and the Hunyuan3D-2.1 figurine at 1.0 mm sliced when remeshed directly but not when repaired first (\"There is an object with no extrusions in the first layer\")."
 ],
 "rows": [
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "none",
   "ok": true,
   "faces": 284010,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 5,
   "shells": 6,
   "genus": null,
   "solid_share_pct": 1.1,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 1.32,
   "print_time": "42m 51s",
   "slicer_output": [
    "Empty layer between 71.75 and 72.65.",
    "Object name: pumpkin__trellis2-80mm.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-none.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.67,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.67
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "windows",
   "ok": true,
   "faces": 284000,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 5,
   "solid_share_pct": 1.1,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 1.31,
   "print_time": "42m 43s",
   "slicer_output": [
    "Empty layer between 71.75 and 72.35.",
    "Object name: pumpkin__trellis2-repaired.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-windows.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.67,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.67
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "fill_holes",
   "ok": true,
   "faces": 284010,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 5,
   "shells": 6,
   "genus": null,
   "solid_share_pct": 1.1,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 1.32,
   "print_time": "42m 51s",
   "slicer_output": [
    "Empty layer between 71.75 and 72.65.",
    "Object name: pumpkin__trellis2__fill_holes.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.67,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.67
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "make_manifold",
   "ok": true,
   "faces": 284000,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 5,
   "solid_share_pct": 1.1,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 1.32,
   "print_time": "42m 49s",
   "slicer_output": [
    "Empty layer between 71.75 and 72.65.",
    "Object name: pumpkin__trellis2__make_manifold.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.67,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.67,
   "repair_seconds": 0.8
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "voxel_05",
   "ok": true,
   "faces": 225620,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 9667,
   "genus": 7,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "gcode": true,
   "filament_m": 0.03,
   "print_time": "1m 48s",
   "slicer_output": [
    "(Some lines not shown)",
    "Object name: pumpkin__trellis2__voxel_05.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.544,
   "removed_p99_mm": 1.7,
   "added_mean_mm": 0.291,
   "added_p99_mm": 0.67,
   "repair_seconds": 0.4
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "voxel_10",
   "ok": true,
   "faces": 32392,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2091,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "gcode": false,
   "filament_m": null,
   "print_time": null,
   "slicer_output": [
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "There is an object with no extrusions in the first layer.",
    "Object name: pumpkin__trellis2__voxel_10.stl"
   ],
   "removed_mean_mm": 1.293,
   "removed_p99_mm": 4.22,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.68,
   "repair_seconds": 0.3
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 225716,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 1,
   "shells": 9678,
   "genus": null,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "gcode": true,
   "filament_m": 0.03,
   "print_time": "1m 54s",
   "slicer_output": [
    "(Some lines not shown)",
    "Object name: pumpkin__trellis2__win_voxel_05.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.541,
   "removed_p99_mm": 1.68,
   "added_mean_mm": 0.29,
   "added_p99_mm": 0.67,
   "repair_seconds": 0.4
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 32412,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2088,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "gcode": true,
   "filament_m": 0.02,
   "print_time": "32s",
   "slicer_output": [
    "(Some lines not shown)",
    "Object name: pumpkin__trellis2__win_voxel_10.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 1.281,
   "removed_p99_mm": 4.21,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.67,
   "repair_seconds": 0.3
  },
  {
   "tag": "pumpkin__trellis2",
   "input": "pumpkin",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "solidify_12",
   "ok": true,
   "faces": 568030,
   "watertight": false,
   "boundary_edges": 10,
   "nonmanifold_edges": 10,
   "shells": 7,
   "genus": null,
   "solid_share_pct": 15.3,
   "thinnest_wall_mm": 1.08,
   "gcode": true,
   "filament_m": 16.31,
   "print_time": "2h 53m 47s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__trellis2-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.409,
   "removed_p99_mm": 0.95,
   "added_mean_mm": 0.711,
   "added_p99_mm": 1.28,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "none",
   "ok": true,
   "faces": 276809,
   "watertight": false,
   "boundary_edges": 3,
   "nonmanifold_edges": 15,
   "shells": 6,
   "genus": null,
   "solid_share_pct": 2.4,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.49,
   "print_time": "21m 20s",
   "slicer_output": [
    "mug__trellis2-80mm.stl",
    "Floating object part, Floating bridge anchors, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-none.gcode"
   ],
   "removed_mean_mm": 0.322,
   "removed_p99_mm": 0.74,
   "added_mean_mm": 0.323,
   "added_p99_mm": 0.74
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "windows",
   "ok": true,
   "faces": 276818,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 12,
   "solid_share_pct": 2.4,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.49,
   "print_time": "21m 40s",
   "slicer_output": [
    "Empty layer between 58.55 and 59.15.",
    "Object name: mug__trellis2-repaired.stl",
    "Make sure the object is printable. This is usually caused by negligibly small extrusions or by a faulty model. Try to repair the model or change its orientation on the bed.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-windows.gcode"
   ],
   "removed_mean_mm": 0.322,
   "removed_p99_mm": 0.73,
   "added_mean_mm": 0.324,
   "added_p99_mm": 0.74
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "fill_holes",
   "ok": true,
   "faces": 276809,
   "watertight": false,
   "boundary_edges": 3,
   "nonmanifold_edges": 15,
   "shells": 6,
   "genus": null,
   "solid_share_pct": 2.4,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.49,
   "print_time": "21m 20s",
   "slicer_output": [
    "mug__trellis2__fill_holes.stl",
    "Floating object part, Floating bridge anchors, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.322,
   "removed_p99_mm": 0.74,
   "added_mean_mm": 0.323,
   "added_p99_mm": 0.74
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "make_manifold",
   "ok": true,
   "faces": 276750,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 1,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 2.4,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.49,
   "print_time": "21m 25s",
   "slicer_output": [
    "mug__trellis2__make_manifold.stl",
    "Floating object part, Floating bridge anchors, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.322,
   "removed_p99_mm": 0.73,
   "added_mean_mm": 0.323,
   "added_p99_mm": 0.74,
   "repair_seconds": 1.8
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "voxel_05",
   "ok": true,
   "faces": 249248,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 8176,
   "genus": null,
   "solid_share_pct": 0.1,
   "thinnest_wall_mm": 0.04,
   "gcode": false,
   "filament_m": null,
   "print_time": null,
   "slicer_output": [
    "Floating object part, Loose extrusions",
    "Consider enabling supports.",
    "There is an object with no extrusions in the first layer.",
    "Object name: mug__trellis2__voxel_05.stl"
   ],
   "removed_mean_mm": 0.539,
   "removed_p99_mm": 1.81,
   "added_mean_mm": 0.317,
   "added_p99_mm": 0.73,
   "repair_seconds": 0.4
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "voxel_10",
   "ok": true,
   "faces": 60552,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 2,
   "solid_share_pct": 18.3,
   "thinnest_wall_mm": 1.92,
   "gcode": true,
   "filament_m": 9.65,
   "print_time": "1h 43m 57s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.325,
   "removed_p99_mm": 0.73,
   "added_mean_mm": 0.323,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.3
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 249420,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 8186,
   "genus": null,
   "solid_share_pct": 0.1,
   "thinnest_wall_mm": 0.04,
   "gcode": false,
   "filament_m": null,
   "print_time": null,
   "slicer_output": [
    "Floating object part, Loose extrusions",
    "Consider enabling supports.",
    "There is an object with no extrusions in the first layer.",
    "Object name: mug__trellis2__win_voxel_05.stl"
   ],
   "removed_mean_mm": 0.541,
   "removed_p99_mm": 1.82,
   "added_mean_mm": 0.317,
   "added_p99_mm": 0.73,
   "repair_seconds": 0.4
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 60548,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 2,
   "solid_share_pct": 18.3,
   "thinnest_wall_mm": 1.92,
   "gcode": true,
   "filament_m": 9.64,
   "print_time": "1h 43m 50s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.325,
   "removed_p99_mm": 0.74,
   "added_mean_mm": 0.324,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.3
  },
  {
   "tag": "mug__trellis2",
   "input": "mug",
   "generator": "trellis2",
   "defect": "hollow skin",
   "method": "solidify_12",
   "ok": true,
   "faces": 553630,
   "watertight": false,
   "boundary_edges": 10,
   "nonmanifold_edges": 30,
   "shells": 6,
   "genus": null,
   "solid_share_pct": 32.3,
   "thinnest_wall_mm": 0.54,
   "gcode": true,
   "filament_m": 14.95,
   "print_time": "2h 53m 30s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__trellis2-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.44,
   "removed_p99_mm": 0.99,
   "added_mean_mm": 0.677,
   "added_p99_mm": 1.29,
   "repair_seconds": 0.1
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "none",
   "ok": true,
   "faces": 292138,
   "watertight": false,
   "boundary_edges": 401,
   "nonmanifold_edges": 20,
   "shells": 8,
   "genus": null,
   "solid_share_pct": 3.6,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.98,
   "print_time": "19m 25s",
   "slicer_output": [
    "charger__trellis2-80mm.stl",
    "Floating object part, Collapsing overhang, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-none.gcode"
   ],
   "removed_mean_mm": 0.349,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.35,
   "added_p99_mm": 0.72
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "windows",
   "ok": true,
   "faces": 278678,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 17,
   "solid_share_pct": 3.8,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.6,
   "print_time": "18m 36s",
   "slicer_output": [
    "charger__trellis2-repaired.stl",
    "Floating object part, Collapsing overhang, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-windows.gcode"
   ],
   "removed_mean_mm": 0.352,
   "removed_p99_mm": 0.74,
   "added_mean_mm": 0.351,
   "added_p99_mm": 0.72
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "fill_holes",
   "ok": true,
   "faces": 292246,
   "watertight": false,
   "boundary_edges": 77,
   "nonmanifold_edges": 20,
   "shells": 8,
   "genus": null,
   "solid_share_pct": 3.6,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.5,
   "print_time": "16m 47s",
   "slicer_output": [
    "charger__trellis2__fill_holes.stl",
    "Floating object part, Collapsing overhang, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.349,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.35,
   "added_p99_mm": 0.72
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "make_manifold",
   "ok": true,
   "faces": 285278,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 7,
   "solid_share_pct": 3.9,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 0.61,
   "print_time": "18m 7s",
   "slicer_output": [
    "charger__trellis2__make_manifold.stl",
    "Floating object part, Collapsing overhang, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.35,
   "removed_p99_mm": 0.73,
   "added_mean_mm": 0.35,
   "added_p99_mm": 0.72,
   "repair_seconds": 2.4
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "voxel_05",
   "ok": true,
   "faces": 119536,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.4,
   "thinnest_wall_mm": 31.87,
   "gcode": true,
   "filament_m": 14.43,
   "print_time": "1h 45m 10s",
   "slicer_output": [
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.477,
   "removed_p99_mm": 0.91,
   "added_mean_mm": 0.355,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.5
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "voxel_10",
   "ok": true,
   "faces": 29548,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.7,
   "thinnest_wall_mm": 31.87,
   "gcode": true,
   "filament_m": 14.36,
   "print_time": "1h 44m 9s",
   "slicer_output": [
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.475,
   "removed_p99_mm": 0.92,
   "added_mean_mm": 0.356,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.3
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 121760,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.4,
   "thinnest_wall_mm": 31.87,
   "gcode": true,
   "filament_m": 14.42,
   "print_time": "1h 45m 8s",
   "slicer_output": [
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.477,
   "removed_p99_mm": 0.91,
   "added_mean_mm": 0.357,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.5
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 30612,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.7,
   "thinnest_wall_mm": 31.87,
   "gcode": true,
   "filament_m": 14.36,
   "print_time": "1h 44m 53s",
   "slicer_output": [
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.475,
   "removed_p99_mm": 0.92,
   "added_mean_mm": 0.356,
   "added_p99_mm": 0.74,
   "repair_seconds": 0.3
  },
  {
   "tag": "charger__trellis2",
   "input": "charger",
   "generator": "trellis2",
   "defect": "hollow skin, 401 open edges",
   "method": "solidify_12",
   "ok": true,
   "faces": 585084,
   "watertight": false,
   "boundary_edges": 8,
   "nonmanifold_edges": 40,
   "shells": 11,
   "genus": null,
   "solid_share_pct": 48.8,
   "thinnest_wall_mm": 0.16,
   "gcode": true,
   "filament_m": 14.9,
   "print_time": "2h 31m 58s",
   "slicer_output": [
    "charger__trellis2__solidify_12.stl",
    "Collapsing overhang, Long bridging extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-charger__trellis2-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.45,
   "removed_p99_mm": 0.86,
   "added_mean_mm": 0.628,
   "added_p99_mm": 1.32,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "none",
   "ok": true,
   "faces": 291026,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 266,
   "shells": 68,
   "genus": null,
   "solid_share_pct": 1.9,
   "thinnest_wall_mm": 0.15,
   "gcode": true,
   "filament_m": 0.78,
   "print_time": "41m 33s",
   "slicer_output": [
    "Floating object part, Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-none.gcode"
   ],
   "removed_mean_mm": 0.252,
   "removed_p99_mm": 0.55,
   "added_mean_mm": 0.252,
   "added_p99_mm": 0.56
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "windows",
   "ok": true,
   "faces": 291102,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 185,
   "solid_share_pct": 1.9,
   "thinnest_wall_mm": 0.15,
   "gcode": true,
   "filament_m": 0.78,
   "print_time": "41m 30s",
   "slicer_output": [
    "Floating object part, Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-windows.gcode"
   ],
   "removed_mean_mm": 0.252,
   "removed_p99_mm": 0.56,
   "added_mean_mm": 0.252,
   "added_p99_mm": 0.55
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "fill_holes",
   "ok": true,
   "faces": 291026,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 266,
   "shells": 68,
   "genus": null,
   "solid_share_pct": 1.9,
   "thinnest_wall_mm": 0.15,
   "gcode": true,
   "filament_m": 0.78,
   "print_time": "41m 33s",
   "slicer_output": [
    "Floating object part, Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.252,
   "removed_p99_mm": 0.55,
   "added_mean_mm": 0.252,
   "added_p99_mm": 0.56
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "make_manifold",
   "ok": true,
   "faces": 289464,
   "watertight": false,
   "boundary_edges": 52,
   "nonmanifold_edges": 9,
   "shells": 11,
   "genus": null,
   "solid_share_pct": -0.0,
   "thinnest_wall_mm": 0.15,
   "gcode": true,
   "filament_m": 2.43,
   "print_time": "1h 2m 44s",
   "slicer_output": [
    "Floating object part, Collapsing overhang, Low bed adhesion, Loose extrusions, Long bridging extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.252,
   "removed_p99_mm": 0.56,
   "added_mean_mm": 0.252,
   "added_p99_mm": 0.56,
   "repair_seconds": 3.2
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "voxel_05",
   "ok": true,
   "faces": 133876,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 14,
   "solid_share_pct": 56.4,
   "thinnest_wall_mm": 36.59,
   "gcode": true,
   "filament_m": 8.79,
   "print_time": "1h 29m 46s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.329,
   "removed_p99_mm": 2.66,
   "added_mean_mm": 0.257,
   "added_p99_mm": 0.56,
   "repair_seconds": 0.4
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "voxel_10",
   "ok": true,
   "faces": 32276,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 57.1,
   "thinnest_wall_mm": 37.25,
   "gcode": true,
   "filament_m": 8.56,
   "print_time": "1h 23m 58s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Thin fragile part",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.423,
   "removed_p99_mm": 3.89,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.68,
   "repair_seconds": 0.2
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 133860,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 14,
   "solid_share_pct": 56.4,
   "thinnest_wall_mm": 36.59,
   "gcode": true,
   "filament_m": 8.79,
   "print_time": "1h 29m 39s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.329,
   "removed_p99_mm": 2.64,
   "added_mean_mm": 0.256,
   "added_p99_mm": 0.56,
   "repair_seconds": 0.4
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 32268,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 57.1,
   "thinnest_wall_mm": 37.25,
   "gcode": true,
   "filament_m": 8.56,
   "print_time": "1h 23m 59s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Thin fragile part",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.423,
   "removed_p99_mm": 3.88,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.68,
   "repair_seconds": 0.2
  },
  {
   "tag": "figurine__trellis2",
   "input": "figurine",
   "generator": "trellis2",
   "defect": "hollow skin, 68 shells",
   "method": "solidify_12",
   "ok": true,
   "faces": 582066,
   "watertight": false,
   "boundary_edges": 66,
   "nonmanifold_edges": 530,
   "shells": 91,
   "genus": null,
   "solid_share_pct": 25.7,
   "thinnest_wall_mm": 0.12,
   "gcode": true,
   "filament_m": 10.73,
   "print_time": "2h 31m 48s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__trellis2-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.354,
   "removed_p99_mm": 0.81,
   "added_mean_mm": 0.646,
   "added_p99_mm": 1.24,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "none",
   "ok": true,
   "faces": 32104,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.2,
   "thinnest_wall_mm": 3.43,
   "gcode": true,
   "filament_m": 16.44,
   "print_time": "2h 11m 49s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-none.gcode"
   ],
   "removed_mean_mm": 0.251,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "windows",
   "ok": true,
   "faces": 32080,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.2,
   "thinnest_wall_mm": 3.43,
   "gcode": true,
   "filament_m": 16.44,
   "print_time": "2h 11m 43s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-windows.gcode"
   ],
   "removed_mean_mm": 0.251,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "fill_holes",
   "ok": true,
   "faces": 32104,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.2,
   "thinnest_wall_mm": 3.43,
   "gcode": true,
   "filament_m": 16.44,
   "print_time": "2h 11m 49s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.251,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "make_manifold",
   "ok": true,
   "faces": 32104,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.2,
   "thinnest_wall_mm": 3.43,
   "gcode": true,
   "filament_m": 16.44,
   "print_time": "2h 11m 49s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.251,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "voxel_05",
   "ok": true,
   "faces": 174036,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.4,
   "thinnest_wall_mm": 3.42,
   "gcode": true,
   "filament_m": 16.41,
   "print_time": "2h 11m 13s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.25,
   "removed_p99_mm": 0.6,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "voxel_10",
   "ok": true,
   "faces": 43408,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.6,
   "thinnest_wall_mm": 3.4,
   "gcode": true,
   "filament_m": 16.37,
   "print_time": "2h 10m 53s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.255,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.253,
   "added_p99_mm": 0.6,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 174016,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.4,
   "thinnest_wall_mm": 3.42,
   "gcode": true,
   "filament_m": 16.41,
   "print_time": "2h 11m 13s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.249,
   "removed_p99_mm": 0.6,
   "added_mean_mm": 0.25,
   "added_p99_mm": 0.6,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 43408,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 85.6,
   "thinnest_wall_mm": 3.4,
   "gcode": true,
   "filament_m": 16.37,
   "print_time": "2h 11m 0s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.255,
   "removed_p99_mm": 0.61,
   "added_mean_mm": 0.254,
   "added_p99_mm": 0.6,
   "repair_seconds": 0.1
  },
  {
   "tag": "mug__sf3d",
   "input": "mug",
   "generator": "sf3d",
   "defect": "opening sealed, solid",
   "method": "solidify_12",
   "ok": true,
   "faces": 64208,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 2,
   "solid_share_pct": 11.6,
   "thinnest_wall_mm": 1.21,
   "gcode": true,
   "filament_m": 6.94,
   "print_time": "1h 19m 7s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__sf3d-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.346,
   "removed_p99_mm": 0.84,
   "added_mean_mm": 0.716,
   "added_p99_mm": 1.32,
   "repair_seconds": 0.0
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "none",
   "ok": true,
   "faces": 453880,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 19.0,
   "thinnest_wall_mm": 0.47,
   "gcode": true,
   "filament_m": 5.7,
   "print_time": "1h 12m 48s",
   "slicer_output": [
    "figurine__hunyuan21-80mm.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-none.gcode"
   ],
   "removed_mean_mm": 0.281,
   "removed_p99_mm": 0.62,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.63
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "windows",
   "ok": true,
   "faces": 453390,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 19.0,
   "thinnest_wall_mm": 0.47,
   "gcode": true,
   "filament_m": 5.7,
   "print_time": "1h 12m 48s",
   "slicer_output": [
    "figurine__hunyuan21-repaired.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-windows.gcode"
   ],
   "removed_mean_mm": 0.28,
   "removed_p99_mm": 0.63,
   "added_mean_mm": 0.281,
   "added_p99_mm": 0.63
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "fill_holes",
   "ok": true,
   "faces": 453880,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 19.0,
   "thinnest_wall_mm": 0.47,
   "gcode": true,
   "filament_m": 5.7,
   "print_time": "1h 12m 48s",
   "slicer_output": [
    "figurine__hunyuan21__fill_holes.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.281,
   "removed_p99_mm": 0.62,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.63
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "make_manifold",
   "ok": true,
   "faces": 453826,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 19.0,
   "thinnest_wall_mm": 0.47,
   "gcode": true,
   "filament_m": 5.7,
   "print_time": "1h 12m 47s",
   "slicer_output": [
    "figurine__hunyuan21__make_manifold.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.281,
   "removed_p99_mm": 0.62,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.63,
   "repair_seconds": 1.2
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "voxel_05",
   "ok": true,
   "faces": 177472,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 5,
   "genus": 11,
   "solid_share_pct": 19.1,
   "thinnest_wall_mm": 0.66,
   "gcode": true,
   "filament_m": 5.5,
   "print_time": "1h 10m 33s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.291,
   "removed_p99_mm": 0.68,
   "added_mean_mm": 0.285,
   "added_p99_mm": 0.62,
   "repair_seconds": 0.4
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "voxel_10",
   "ok": true,
   "faces": 43572,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 8,
   "solid_share_pct": 19.4,
   "thinnest_wall_mm": 39.31,
   "gcode": true,
   "filament_m": 5.36,
   "print_time": "1h 9m 46s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.317,
   "removed_p99_mm": 0.99,
   "added_mean_mm": 0.298,
   "added_p99_mm": 0.66,
   "repair_seconds": 0.3
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 177476,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 5,
   "genus": 11,
   "solid_share_pct": 19.1,
   "thinnest_wall_mm": 0.66,
   "gcode": true,
   "filament_m": 5.5,
   "print_time": "1h 10m 38s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.29,
   "removed_p99_mm": 0.67,
   "added_mean_mm": 0.285,
   "added_p99_mm": 0.63,
   "repair_seconds": 0.5
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 43576,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 8,
   "solid_share_pct": 19.4,
   "thinnest_wall_mm": 39.31,
   "gcode": false,
   "filament_m": null,
   "print_time": null,
   "slicer_output": [
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "There is an object with no extrusions in the first layer.",
    "Object name: figurine__hunyuan21__win_voxel_10.stl"
   ],
   "removed_mean_mm": 0.319,
   "removed_p99_mm": 1.0,
   "added_mean_mm": 0.299,
   "added_p99_mm": 0.65,
   "repair_seconds": 0.3
  },
  {
   "tag": "figurine__hunyuan21",
   "input": "figurine",
   "generator": "hunyuan21",
   "defect": "thin sheet under the figurine",
   "method": "solidify_12",
   "ok": true,
   "faces": 907760,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 20,
   "solid_share_pct": 13.7,
   "thinnest_wall_mm": 0.73,
   "gcode": true,
   "filament_m": 7.47,
   "print_time": "1h 43m 39s",
   "slicer_output": [
    "Floating bridge anchors, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__hunyuan21-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.382,
   "removed_p99_mm": 0.85,
   "added_mean_mm": 0.582,
   "added_p99_mm": 1.31,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "none",
   "ok": true,
   "faces": 99996,
   "watertight": false,
   "boundary_edges": 8,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 63.6,
   "thinnest_wall_mm": 3.56,
   "gcode": true,
   "filament_m": 8.66,
   "print_time": "1h 32m 48s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-none.gcode"
   ],
   "removed_mean_mm": 0.218,
   "removed_p99_mm": 0.53,
   "added_mean_mm": 0.218,
   "added_p99_mm": 0.53
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "windows",
   "ok": true,
   "faces": 100004,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 14,
   "solid_share_pct": 63.6,
   "thinnest_wall_mm": 3.56,
   "gcode": true,
   "filament_m": 8.67,
   "print_time": "1h 32m 45s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-windows.gcode"
   ],
   "removed_mean_mm": 0.218,
   "removed_p99_mm": 0.53,
   "added_mean_mm": 0.218,
   "added_p99_mm": 0.53
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "fill_holes",
   "ok": true,
   "faces": 100000,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 63.6,
   "thinnest_wall_mm": 3.56,
   "gcode": true,
   "filament_m": 8.66,
   "print_time": "1h 32m 49s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.218,
   "removed_p99_mm": 0.52,
   "added_mean_mm": 0.218,
   "added_p99_mm": 0.53
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "make_manifold",
   "ok": true,
   "faces": 100000,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 63.6,
   "thinnest_wall_mm": 3.56,
   "gcode": true,
   "filament_m": 8.66,
   "print_time": "1h 32m 50s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.218,
   "removed_p99_mm": 0.52,
   "added_mean_mm": 0.218,
   "added_p99_mm": 0.53,
   "repair_seconds": 0.3
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "voxel_05",
   "ok": true,
   "faces": 128136,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 64.1,
   "thinnest_wall_mm": 3.67,
   "gcode": true,
   "filament_m": 8.43,
   "print_time": "1h 27m 0s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.256,
   "removed_p99_mm": 1.32,
   "added_mean_mm": 0.227,
   "added_p99_mm": 0.53,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "voxel_10",
   "ok": true,
   "faces": 30236,
   "watertight": false,
   "boundary_edges": 0,
   "nonmanifold_edges": 2,
   "shells": 2,
   "genus": null,
   "solid_share_pct": 65.1,
   "thinnest_wall_mm": 39.09,
   "gcode": true,
   "filament_m": 8.23,
   "print_time": "1h 20m 18s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion, Thin fragile part",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.374,
   "removed_p99_mm": 2.64,
   "added_mean_mm": 0.26,
   "added_p99_mm": 0.69,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 128120,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 8,
   "solid_share_pct": 64.1,
   "thinnest_wall_mm": 3.67,
   "gcode": true,
   "filament_m": 8.42,
   "print_time": "1h 26m 53s",
   "slicer_output": [
    "Floating object part, Floating bridge anchors, Low bed adhesion",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.256,
   "removed_p99_mm": 1.32,
   "added_mean_mm": 0.227,
   "added_p99_mm": 0.53,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 30224,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 7,
   "solid_share_pct": 65.1,
   "thinnest_wall_mm": 39.09,
   "gcode": true,
   "filament_m": 8.23,
   "print_time": "1h 20m 19s",
   "slicer_output": [
    "Collapsing overhang, Low bed adhesion, Thin fragile part",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.374,
   "removed_p99_mm": 2.63,
   "added_mean_mm": 0.26,
   "added_p99_mm": 0.68,
   "repair_seconds": 0.1
  },
  {
   "tag": "figurine__neural4d",
   "input": "figurine",
   "generator": "neural4d",
   "defect": "8 open edges, 2 shells",
   "method": "solidify_12",
   "ok": true,
   "faces": 200008,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 3,
   "genus": 29,
   "solid_share_pct": 14.7,
   "thinnest_wall_mm": 1.22,
   "gcode": true,
   "filament_m": 4.79,
   "print_time": "1h 24m 57s",
   "slicer_output": [
    "Floating object part, Collapsing overhang, Low bed adhesion, Loose extrusions",
    "Consider enabling supports.",
    "Also consider enabling brim.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-figurine__neural4d-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.311,
   "removed_p99_mm": 0.74,
   "added_mean_mm": 0.664,
   "added_p99_mm": 1.3,
   "repair_seconds": 0.0
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "none",
   "ok": true,
   "faces": 589094,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.8,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.26,
   "print_time": "2h 11m 52s",
   "slicer_output": [
    "mug__hunyuan21-80mm.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-none.gcode"
   ],
   "removed_mean_mm": 0.298,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "windows",
   "ok": true,
   "faces": 587852,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.8,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.27,
   "print_time": "2h 11m 42s",
   "slicer_output": [
    "mug__hunyuan21-repaired.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-windows.gcode"
   ],
   "removed_mean_mm": 0.296,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.71
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "fill_holes",
   "ok": true,
   "faces": 589094,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.8,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.26,
   "print_time": "2h 11m 52s",
   "slicer_output": [
    "mug__hunyuan21__fill_holes.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.298,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "make_manifold",
   "ok": true,
   "faces": 588970,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.8,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.26,
   "print_time": "2h 11m 57s",
   "slicer_output": [
    "mug__hunyuan21__make_manifold.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.298,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72,
   "repair_seconds": 1.8
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "voxel_05",
   "ok": true,
   "faces": 235620,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.23,
   "print_time": "2h 11m 37s",
   "slicer_output": [
    "mug__hunyuan21__voxel_05.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72,
   "repair_seconds": 0.6
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "voxel_10",
   "ok": true,
   "faces": 58936,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.16,
   "print_time": "2h 11m 5s",
   "slicer_output": [
    "mug__hunyuan21__voxel_10.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.301,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.301,
   "added_p99_mm": 0.72,
   "repair_seconds": 0.4
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 235608,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.23,
   "print_time": "2h 11m 33s",
   "slicer_output": [
    "mug__hunyuan21__win_voxel_05.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72,
   "repair_seconds": 0.6
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 58944,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "gcode": true,
   "filament_m": 11.16,
   "print_time": "2h 10m 53s",
   "slicer_output": [
    "mug__hunyuan21__win_voxel_10.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.301,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.301,
   "added_p99_mm": 0.72,
   "repair_seconds": 0.5
  },
  {
   "tag": "mug__hunyuan21",
   "input": "mug",
   "generator": "hunyuan21",
   "defect": "control: healthy hollow mug",
   "method": "solidify_12",
   "ok": true,
   "faces": 1178188,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 2,
   "solid_share_pct": 17.3,
   "thinnest_wall_mm": 1.21,
   "gcode": true,
   "filament_m": 10.12,
   "print_time": "2h 12m 30s",
   "slicer_output": [
    "mug__hunyuan21__solidify_12.stl",
    "Floating bridge anchors, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-mug__hunyuan21-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.415,
   "removed_p99_mm": 1.0,
   "added_mean_mm": 0.759,
   "added_p99_mm": 1.36,
   "repair_seconds": 0.1
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "none",
   "ok": true,
   "faces": 507512,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.4,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.53,
   "print_time": "2h 51m 29s",
   "slicer_output": [
    "pumpkin__hunyuan21-80mm.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-none.gcode"
   ],
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.269,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "windows",
   "ok": true,
   "faces": 506392,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.4,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.53,
   "print_time": "2h 51m 27s",
   "slicer_output": [
    "pumpkin__hunyuan21-repaired.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-windows.gcode"
   ],
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.66,
   "added_mean_mm": 0.268,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "fill_holes",
   "ok": true,
   "faces": 507512,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.4,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.53,
   "print_time": "2h 51m 29s",
   "slicer_output": [
    "pumpkin__hunyuan21__fill_holes.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-fill_holes.gcode"
   ],
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.269,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "make_manifold",
   "ok": true,
   "faces": 507400,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.4,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.53,
   "print_time": "2h 51m 31s",
   "slicer_output": [
    "pumpkin__hunyuan21__make_manifold.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-make_manifold.gcode"
   ],
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.269,
   "added_p99_mm": 0.65,
   "repair_seconds": 1.4
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "voxel_05",
   "ok": true,
   "faces": 202880,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.51,
   "print_time": "2h 51m 36s",
   "slicer_output": [
    "pumpkin__hunyuan21__voxel_05.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-voxel_05.gcode"
   ],
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.66,
   "added_mean_mm": 0.269,
   "added_p99_mm": 0.65,
   "repair_seconds": 0.5
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "voxel_10",
   "ok": true,
   "faces": 50624,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.06,
   "gcode": true,
   "filament_m": 23.48,
   "print_time": "2h 50m 54s",
   "slicer_output": [
    "pumpkin__hunyuan21__voxel_10.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-voxel_10.gcode"
   ],
   "removed_mean_mm": 0.273,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.272,
   "added_p99_mm": 0.65,
   "repair_seconds": 0.4
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "win_voxel_05",
   "ok": true,
   "faces": 202876,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.07,
   "gcode": true,
   "filament_m": 23.52,
   "print_time": "2h 51m 14s",
   "slicer_output": [
    "pumpkin__hunyuan21__win_voxel_05.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-win_voxel_05.gcode"
   ],
   "removed_mean_mm": 0.27,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.27,
   "added_p99_mm": 0.65,
   "repair_seconds": 0.5
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "win_voxel_10",
   "ok": true,
   "faces": 50624,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.06,
   "gcode": true,
   "filament_m": 23.48,
   "print_time": "2h 50m 50s",
   "slicer_output": [
    "pumpkin__hunyuan21__win_voxel_10.stl",
    "Collapsing overhang",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-win_voxel_10.gcode"
   ],
   "removed_mean_mm": 0.273,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.273,
   "added_p99_mm": 0.65,
   "repair_seconds": 0.4
  },
  {
   "tag": "pumpkin__hunyuan21",
   "input": "pumpkin",
   "generator": "hunyuan21",
   "defect": "control: healthy, carved face",
   "method": "solidify_12",
   "ok": true,
   "faces": 1015024,
   "watertight": true,
   "boundary_edges": 0,
   "nonmanifold_edges": 0,
   "shells": 2,
   "genus": 0,
   "solid_share_pct": 9.6,
   "thinnest_wall_mm": 1.24,
   "gcode": true,
   "filament_m": 8.16,
   "print_time": "1h 31m 51s",
   "slicer_output": [
    "pumpkin__hunyuan21__solidify_12.stl",
    "Collapsing overhang, Loose extrusions",
    "Consider enabling supports.",
    "Slicing result exported to D:\\SEO_Workflows\\3d-tools-site\\tmp-gen\\baseline\\work\\repair-pumpkin__hunyuan21-solidify_12.gcode"
   ],
   "removed_mean_mm": 0.375,
   "removed_p99_mm": 0.91,
   "added_mean_mm": 0.736,
   "added_p99_mm": 1.34,
   "repair_seconds": 0.1
  }
 ],
 "voxel_sweep": [
  {
   "tag": "pumpkin__trellis2",
   "voxel_mm": 0.5,
   "watertight": true,
   "shells": 9667,
   "genus": 7,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "removed_mean_mm": 0.544,
   "removed_p99_mm": 1.7,
   "added_mean_mm": 0.291,
   "added_p99_mm": 0.67
  },
  {
   "tag": "pumpkin__trellis2",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 2091,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "removed_mean_mm": 1.293,
   "removed_p99_mm": 4.22,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.68
  },
  {
   "tag": "pumpkin__trellis2",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 718,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "removed_mean_mm": 2.178,
   "removed_p99_mm": 5.64,
   "added_mean_mm": 0.334,
   "added_p99_mm": 0.85
  },
  {
   "tag": "pumpkin__trellis2",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 338,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "removed_mean_mm": 3.378,
   "removed_p99_mm": 9.33,
   "added_mean_mm": 0.356,
   "added_p99_mm": 0.97
  },
  {
   "tag": "pumpkin__trellis2",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 102,
   "genus": 0,
   "solid_share_pct": 0.0,
   "thinnest_wall_mm": null,
   "removed_mean_mm": 6.278,
   "removed_p99_mm": 15.38,
   "added_mean_mm": 0.555,
   "added_p99_mm": 1.62
  },
  {
   "tag": "mug__trellis2",
   "voxel_mm": 0.5,
   "watertight": false,
   "shells": 8176,
   "genus": null,
   "solid_share_pct": 0.1,
   "thinnest_wall_mm": 0.04,
   "removed_mean_mm": 0.539,
   "removed_p99_mm": 1.81,
   "added_mean_mm": 0.317,
   "added_p99_mm": 0.73
  },
  {
   "tag": "mug__trellis2",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 1,
   "genus": 2,
   "solid_share_pct": 18.3,
   "thinnest_wall_mm": 1.92,
   "removed_mean_mm": 0.325,
   "removed_p99_mm": 0.73,
   "added_mean_mm": 0.323,
   "added_p99_mm": 0.74
  },
  {
   "tag": "mug__trellis2",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 1,
   "genus": 2,
   "solid_share_pct": 18.2,
   "thinnest_wall_mm": 1.89,
   "removed_mean_mm": 0.335,
   "removed_p99_mm": 0.76,
   "added_mean_mm": 0.331,
   "added_p99_mm": 0.74
  },
  {
   "tag": "mug__trellis2",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 1,
   "genus": 4,
   "solid_share_pct": 17.4,
   "thinnest_wall_mm": 1.25,
   "removed_mean_mm": 0.364,
   "removed_p99_mm": 1.0,
   "added_mean_mm": 0.353,
   "added_p99_mm": 0.81
  },
  {
   "tag": "mug__trellis2",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 2,
   "genus": 29,
   "solid_share_pct": 12.2,
   "thinnest_wall_mm": 1.06,
   "removed_mean_mm": 0.793,
   "removed_p99_mm": 3.64,
   "added_mean_mm": 0.487,
   "added_p99_mm": 1.09
  },
  {
   "tag": "charger__trellis2",
   "voxel_mm": 0.5,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.4,
   "thinnest_wall_mm": 31.87,
   "removed_mean_mm": 0.477,
   "removed_p99_mm": 0.91,
   "added_mean_mm": 0.355,
   "added_p99_mm": 0.74
  },
  {
   "tag": "charger__trellis2",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.7,
   "thinnest_wall_mm": 31.87,
   "removed_mean_mm": 0.475,
   "removed_p99_mm": 0.92,
   "added_mean_mm": 0.356,
   "added_p99_mm": 0.74
  },
  {
   "tag": "charger__trellis2",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 90.8,
   "thinnest_wall_mm": 31.83,
   "removed_mean_mm": 0.469,
   "removed_p99_mm": 1.06,
   "added_mean_mm": 0.355,
   "added_p99_mm": 0.75
  },
  {
   "tag": "charger__trellis2",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 91.6,
   "thinnest_wall_mm": 31.87,
   "removed_mean_mm": 0.48,
   "removed_p99_mm": 1.23,
   "added_mean_mm": 0.359,
   "added_p99_mm": 0.77
  },
  {
   "tag": "charger__trellis2",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 91.9,
   "thinnest_wall_mm": 31.83,
   "removed_mean_mm": 0.52,
   "removed_p99_mm": 2.19,
   "added_mean_mm": 0.378,
   "added_p99_mm": 1.05
  },
  {
   "tag": "figurine__trellis2",
   "voxel_mm": 0.5,
   "watertight": true,
   "shells": 1,
   "genus": 14,
   "solid_share_pct": 56.4,
   "thinnest_wall_mm": 36.59,
   "removed_mean_mm": 0.329,
   "removed_p99_mm": 2.66,
   "added_mean_mm": 0.257,
   "added_p99_mm": 0.56
  },
  {
   "tag": "figurine__trellis2",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 1,
   "genus": 10,
   "solid_share_pct": 57.1,
   "thinnest_wall_mm": 37.25,
   "removed_mean_mm": 0.423,
   "removed_p99_mm": 3.89,
   "added_mean_mm": 0.282,
   "added_p99_mm": 0.68
  },
  {
   "tag": "figurine__trellis2",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 22,
   "genus": 1,
   "solid_share_pct": 58.0,
   "thinnest_wall_mm": 37.55,
   "removed_mean_mm": 0.552,
   "removed_p99_mm": 4.45,
   "added_mean_mm": 0.33,
   "added_p99_mm": 0.91
  },
  {
   "tag": "figurine__trellis2",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 19,
   "genus": 1,
   "solid_share_pct": 59.1,
   "thinnest_wall_mm": 37.27,
   "removed_mean_mm": 0.68,
   "removed_p99_mm": 4.73,
   "added_mean_mm": 0.373,
   "added_p99_mm": 1.13
  },
  {
   "tag": "figurine__trellis2",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 5,
   "genus": 0,
   "solid_share_pct": 76.1,
   "thinnest_wall_mm": 37.32,
   "removed_mean_mm": 1.689,
   "removed_p99_mm": 20.69,
   "added_mean_mm": 0.505,
   "added_p99_mm": 1.82
  },
  {
   "tag": "pumpkin__hunyuan21",
   "voxel_mm": 0.5,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.07,
   "removed_mean_mm": 0.269,
   "removed_p99_mm": 0.66,
   "added_mean_mm": 0.269,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.5,
   "thinnest_wall_mm": 72.06,
   "removed_mean_mm": 0.273,
   "removed_p99_mm": 0.65,
   "added_mean_mm": 0.272,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.6,
   "thinnest_wall_mm": 72.05,
   "removed_mean_mm": 0.28,
   "removed_p99_mm": 0.66,
   "added_mean_mm": 0.28,
   "added_p99_mm": 0.65
  },
  {
   "tag": "pumpkin__hunyuan21",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 93.8,
   "thinnest_wall_mm": 72.04,
   "removed_mean_mm": 0.295,
   "removed_p99_mm": 0.7,
   "added_mean_mm": 0.294,
   "added_p99_mm": 0.69
  },
  {
   "tag": "pumpkin__hunyuan21",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 1,
   "genus": 0,
   "solid_share_pct": 94.2,
   "thinnest_wall_mm": 72.09,
   "removed_mean_mm": 0.344,
   "removed_p99_mm": 0.97,
   "added_mean_mm": 0.34,
   "added_p99_mm": 0.91
  },
  {
   "tag": "mug__hunyuan21",
   "voxel_mm": 0.5,
   "watertight": true,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "removed_mean_mm": 0.297,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.297,
   "added_p99_mm": 0.72
  },
  {
   "tag": "mug__hunyuan21",
   "voxel_mm": 1.0,
   "watertight": true,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 20.9,
   "thinnest_wall_mm": 2.5,
   "removed_mean_mm": 0.301,
   "removed_p99_mm": 0.72,
   "added_mean_mm": 0.301,
   "added_p99_mm": 0.72
  },
  {
   "tag": "mug__hunyuan21",
   "voxel_mm": 1.5,
   "watertight": true,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 21.0,
   "thinnest_wall_mm": 2.51,
   "removed_mean_mm": 0.315,
   "removed_p99_mm": 0.76,
   "added_mean_mm": 0.311,
   "added_p99_mm": 0.73
  },
  {
   "tag": "mug__hunyuan21",
   "voxel_mm": 2.0,
   "watertight": true,
   "shells": 1,
   "genus": 1,
   "solid_share_pct": 21.0,
   "thinnest_wall_mm": 2.47,
   "removed_mean_mm": 0.338,
   "removed_p99_mm": 0.93,
   "added_mean_mm": 0.328,
   "added_p99_mm": 0.82
  },
  {
   "tag": "mug__hunyuan21",
   "voxel_mm": 3.0,
   "watertight": true,
   "shells": 1,
   "genus": 15,
   "solid_share_pct": 18.0,
   "thinnest_wall_mm": 0.62,
   "removed_mean_mm": 0.569,
   "removed_p99_mm": 2.47,
   "added_mean_mm": 0.478,
   "added_p99_mm": 1.27
  }
 ]
}