{
 "measured_on": "2026-11-03",
 "tolerance_mm": 0.3,
 "openscad": "2021.01",
 "prompts": {
  "box": "Write OpenSCAD code for a 3D printable open-top storage box. Outside dimensions 60 mm long, 40 mm wide, 25 mm tall. Walls 2 mm thick, floor 2 mm thick. It should print flat on its base. Reply with the complete .scad file.",
  "plate": "Write OpenSCAD code for a 3D printable mounting plate, 80 mm by 50 mm and 4 mm thick, with four 3.4 mm diameter through holes for M3 screws. The hole centres form a 70 mm by 40 mm rectangle centred on the plate. It should print flat. Reply with the complete .scad file.",
  "bracket": "Write OpenSCAD code for a 3D printable L-shaped shelf bracket. One arm 50 mm long, the other 40 mm long, both 20 mm wide and 4 mm thick, meeting at 90 degrees, with a triangular gusset between them. Put two 4.5 mm screw holes through each arm. It should print without supports. Reply with the complete .scad file.",
  "gear": "Write OpenSCAD code for a 3D printable spur gear: 20 teeth, module 1, 6 mm thick, with a 5 mm diameter centre bore. It should print flat. Reply with the complete .scad file.",
  "adapter": "Write OpenSCAD code for a 3D printable tube adapter that joins a 32 mm outside diameter section to a 25 mm outside diameter section. Each section is 20 mm long, the walls are 2 mm thick everywhere, and it is open all the way through. Reply with the complete .scad file.",
  "tag": "Write OpenSCAD code for a 3D printable name tag: a 50 mm by 20 mm plate, 3 mm thick, with the word TEST raised 1 mm on top and a 4 mm hole near one end for a key ring. Reply with the complete .scad file."
 },
 "failure_categories": {
  "syntax_error": "The file does not parse in OpenSCAD 2021.01: a reserved word such as module used as a parameter name, an invalid list expression, or steps left unfinished as comments.",
  "not_a_file": "The reply mixed explanation and code without separating them, so there is no file to save and open.",
  "not_closed": "A hand-built polyhedron (usually the gear teeth) whose faces do not close, which OpenSCAD refuses to render: \"The given mesh is not closed\".",
  "blind_holes": "Holes that stop short of the far face. In every case here the plate was centred with center=true and the cutting cylinder was not, so it cut only the top half.",
  "holes_wrong_axis": "Holes cut along the wrong axis after the shape was extruded sideways, so none passes through the thickness.",
  "disconnected": "Pieces that should be one part do not touch: text floating 0.5 mm above the plate, or two tube sections whose walls do not overlap and meet only along an edge.",
  "wrong_shape": "A different shape from the one asked for: an L bracket with both arms lying flat on the bed instead of meeting at 90 degrees.",
  "out_of_bounds": "A feature placed past the part's edge: raised text running off the end of the tag.",
  "feature_missing": "A requested feature is absent because of how the code is structured: two top-level difference() blocks, one of which fills the hole the other cut.",
  "no_answer": "No retained initial reply and render outcome for this slot. Includes empty replies and initial provider failures; excluded from answered-run counts.",
  "pass": "Rendered as one closed body and passed the implemented checks. Unchecked requirements remain explicitly listed; this is not complete prompt compliance or print readiness.",
  "measured_check_failed": "A mesh failed at least one implemented check; no more specific code-level cause is asserted.",
  "measurement_error": "Mesh loading or a required measurement failed; never counted as a pass.",
  "render_failed": "Recorded render failure without a more specific reviewed label."
 },
 "summary": {
  "planned_slots": 90,
  "saved_initial_replies": 71,
  "initial_render_recorded": 71,
  "missing_initial_outcomes": 19,
  "initial_provider_errors": 17,
  "repair_provider_errors": 1,
  "repair_replies_saved": 7,
  "models_complete": [
   "deepseek-v4-flash",
   "nemotron-3-ultra"
  ],
  "models_partial": {
   "deepseek-v4-pro": 16,
   "gemini": 9,
   "gemma-4-31b": 10
  },
  "runs": 36,
  "rendered_first": 30,
  "render_failed_first": 6,
  "rendered_after_fix": 2,
  "pass_first": 21,
  "pass_final": 23,
  "rendered_but_wrong": 9,
  "empty_replies_reasked": 9,
  "outcome_first": {
   "pass": 21,
   "disconnected": 4,
   "syntax_error": 3,
   "wrong_shape": 3,
   "not_closed": 2,
   "blind_holes": 2,
   "not_a_file": 1
  },
  "outcome_final": {
   "pass": 23,
   "disconnected": 4,
   "wrong_shape": 3,
   "syntax_error": 2,
   "blind_holes": 2,
   "not_a_file": 1,
   "not_closed": 1
  },
  "per_part": {
   "box": {
    "runs": 6,
    "pass_first": 6,
    "pass_final": 6
   },
   "plate": {
    "runs": 6,
    "pass_first": 5,
    "pass_final": 5
   },
   "bracket": {
    "runs": 6,
    "pass_first": 3,
    "pass_final": 3
   },
   "gear": {
    "runs": 6,
    "pass_first": 0,
    "pass_final": 2
   },
   "adapter": {
    "runs": 6,
    "pass_first": 4,
    "pass_final": 4
   },
   "tag": {
    "runs": 6,
    "pass_first": 3,
    "pass_final": 3
   }
  },
  "per_model": {
   "deepseek-v4-flash": {
    "slots": 18,
    "answered": 18,
    "versions_recorded": [
     "deepseek-flash"
    ],
    "unknown_initial_version": 6,
    "initial_render_failed": 3,
    "repair_provider_errors": 0,
    "pass_first": 15,
    "pass_final": 17
   },
   "deepseek-v4-pro": {
    "slots": 18,
    "answered": 16,
    "versions_recorded": [
     "deepseek-v4-pro"
    ],
    "unknown_initial_version": 0,
    "initial_render_failed": 0,
    "repair_provider_errors": 0,
    "pass_first": 13,
    "pass_final": 13
   },
   "gemini": {
    "slots": 18,
    "answered": 9,
    "versions_recorded": [
     "gemini-3.6-flash",
     "gemini-3.8-flash"
    ],
    "unknown_initial_version": 0,
    "initial_render_failed": 0,
    "repair_provider_errors": 0,
    "pass_first": 9,
    "pass_final": 9
   },
   "gemma-4-31b": {
    "slots": 18,
    "answered": 10,
    "versions_recorded": [
     "google/gemma-4-31b-it:free"
    ],
    "unknown_initial_version": 0,
    "initial_render_failed": 2,
    "repair_provider_errors": 1,
    "pass_first": 3,
    "pass_final": 4
   },
   "nemotron-3-ultra": {
    "slots": 18,
    "answered": 18,
    "versions_recorded": [
     "nvidia/nemotron-3-ultra-550b-a55b:free"
    ],
    "unknown_initial_version": 0,
    "initial_render_failed": 3,
    "repair_provider_errors": 0,
    "pass_first": 6,
    "pass_final": 6
   }
  }
 },
 "pass_definition": "All implemented checks passed, not every prompt requirement or print readiness.",
 "unchecked_requirements": {
  "box": [
   "Wall thickness away from sampled sections; corner shape"
  ],
  "plate": [
   "Hole centring relative to the plate; mechanical fit"
  ],
  "bracket": [
   "4.5 mm hole diameters and placement on each arm",
   "Arm thickness, gusset shape and right angle",
   "Support-free printing"
  ],
  "gear": [
   "Involute tooth profile, pitch accuracy and meshing with another gear"
  ],
  "adapter": [
   "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
  ],
  "tag": [
   "Literal TEST text and font shape",
   "Independent plate and raised-text thicknesses",
   "Hole placement near an end"
  ]
 },
 "not_measured_here": [
  "GPT and Claude models were not included in these retained runs; no claim about current API pricing or access is made.",
  "Paid text-to-CAD products such as Zoo and TextoCAD, and AI add-ins for FreeCAD or Fusion.",
  "Other code-CAD languages (CadQuery, build123d) and STEP output: every part here is OpenSCAD rendered to STL.",
  "OpenSCAD development snapshots: retained code was rendered with version 2021.01; newer versions were not tested.",
  "Physical prints, strength, fit, support requirements and successful fabrication: mesh checks do not establish these.",
  "Chat interfaces: replies came from each model's API with no system prompt and default settings, which is close to but not the same as a chat app.",
  "Variation beyond three runs per part and model, and any prompt other than the six written here."
 ],
 "rows": [
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "box",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "box",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:01.441Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "box",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:05.383Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "plate",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "plate",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:10.350Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "plate",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:15.434Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "bracket",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1072,
    "extents": [
     50.0,
     20.0,
     40.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 968.2,
    "overhang_mm2": 28.3,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 40",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "bracket",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:32:15.332Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1064,
    "extents": [
     40.0,
     20.0,
     50.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 768.2,
    "overhang_mm2": 28.3,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "40 x 20 x 50",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "bracket",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:33:22.356Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 552,
    "extents": [
     20.0,
     50.0,
     40.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 968.4,
    "overhang_mm2": 28.2,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "20 x 50 x 40",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "gear",
   "run": 1,
   "error": null,
   "rendered": false,
   "fix_rendered": true,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "fixed": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 5312,
    "extents": [
     22.0,
     22.0,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 286.9,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/deepseek-v4-flash/gear-1.scad, line 18",
   "empty_replies": 0,
   "outcome_first": "syntax_error",
   "outcome_final": "pass",
   "failure_note": "module = 1 as a parameter name",
   "final_size_mm": "22 x 22 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": true
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "gear",
   "run": 2,
   "error": null,
   "rendered": false,
   "fix_rendered": true,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:34:32.561Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "fixed": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 3456,
    "extents": [
     22.0,
     22.0,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 286.9,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "render_error": "ERROR: The given mesh is not closed! Unable to convert to CGAL_Nef_Polyhedron.",
   "empty_replies": 0,
   "outcome_first": "not_closed",
   "outcome_final": "pass",
   "final_size_mm": "22 x 22 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": true
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "gear",
   "run": 3,
   "error": null,
   "rendered": false,
   "fix_rendered": false,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:36:23.701Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "render_error": "ERROR: The given mesh is not closed! Unable to convert to CGAL_Nef_Polyhedron.",
   "fix_render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/deepseek-v4-flash/gear-3-fix.scad, line 94",
   "empty_replies": 0,
   "outcome_first": "not_closed",
   "outcome_final": "syntax_error",
   "failure_note": "repair used concat(for ...) without list brackets",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": true
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "adapter",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 2048,
    "extents": [
     32.0,
     32.0,
     43.5
    ],
    "tube_sections": [
     {
      "z": 10.9,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 32.6,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.0,
     "25": 20.0
    },
    "transition_mm": 3.5,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9996002366512293
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9996002366512275
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.9996002366512382
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.9996002366512204
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.999600236651224
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9996002366512116
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.999600236651224
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.999600236651208
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9996002366512027
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.999600236651224
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9996002366512258
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.9996002366512098
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9996002366512258
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.999600236651231
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9996002366512133
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.9996002366512293
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9996002366512187
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.9996002366512275
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9996002366512204
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999600236651231
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.9996001105398715
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9995998583012877
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.9995996060373677
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995993537417238
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9995993537417434
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995993537417256
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.999599353741715
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995993537417451
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995993537417203
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.999599353741731
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.9995993537417185
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9995993537417345
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9995993537417256
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995993537417238
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.9995993537417274
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995993537417363
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995993537417203
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.999599353741731
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995993537417327
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.999599353741747
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.9995993537417167
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9995993537417274
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.9995993537417398
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 43.5",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "adapter",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T10:21:30.770Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 2048,
    "extents": [
     32.0,
     32.0,
     44.0
    ],
    "tube_sections": [
     {
      "z": 11.0,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 33.0,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.0,
     "25": 20.0
    },
    "transition_mm": 4.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.9995940896109943
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.999594089610989
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995940896109996
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9995940896109783
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.99959408961098
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995940896109747
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.9995940896109783
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995940896110014
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995940896109765
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.9995940896110085
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9995940896110103
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995940896109925
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999594089610996
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.9995946754781802
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.999595847201574
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.9995970189080943
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995981905941118
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995987764280567
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995987764280283
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.999598776428023
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.999598776428039
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9995987764280514
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995987764280354
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.9995987764280425
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995987764280478
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995987764280478
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9995987764280319
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 43.5,
      "equivalent_wall_mm": 1.9995987764280425
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 1,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 44",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "adapter",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:41:52.558Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 2048,
    "extents": [
     32.0,
     32.0,
     45.0
    ],
    "tube_sections": [
     {
      "z": 11.2,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 33.8,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.0,
     "25": 20.0
    },
    "transition_mm": 5.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.9995940896109943
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.999594089610989
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995940896109996
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9995940896109783
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.99959408961098
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995940896109747
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9995940896109854
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.9995940896109783
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995940896110014
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995940896109765
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.9995940896110085
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9995940896110103
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.9995940896109907
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995940896109925
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999594089610996
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.9995945583049917
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9995954956861919
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.999596433057162
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995973704162306
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9995983077614028
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995987764280567
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9995987764280283
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.999598776428023
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.999598776428039
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995987764280514
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.9995987764280354
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995987764280425
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995987764280478
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995987764280478
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995987764280372
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.9995987764280319
     },
     {
      "z": 43.5,
      "equivalent_wall_mm": 1.9995987764280443
     },
     {
      "z": 44.5,
      "equivalent_wall_mm": 1.9995987764280425
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 45",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": null,
   "part": "tag",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1436,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "tag",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:42:05.019Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1544,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-flash",
   "model_version": "deepseek-flash",
   "part": "tag",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:42:16.315Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1544,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "box",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:33.100Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "box",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:31:39.823Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "box",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:31:51.246Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "plate",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:32:03.741Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "plate",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:32:31.113Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "plate",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:32:51.319Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "bracket",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T10:43:29.956Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1064,
    "extents": [
     50.0,
     20.0,
     40.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 968.2,
    "overhang_mm2": 28.3,
    "all_checks_pass": true
   },
   "empty_replies": 3,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 40",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "bracket",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T10:55:49.826Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1064,
    "extents": [
     50.0,
     40.0,
     4.0
    ],
    "size_ok": false,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 1449.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 2,
   "outcome_first": "wrong_shape",
   "outcome_final": "wrong_shape",
   "failure_note": "Code extrudes a planar XY L profile to 4 mm, rather than joining two shelf-support arms in perpendicular planes.",
   "final_size_mm": "50 x 40 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "bracket",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T11:02:09.092Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 288,
    "extents": [
     40.0,
     50.0,
     20.0
    ],
    "size_ok": true,
    "genus": 0,
    "through_holes_ok": false,
    "bed_contact_mm2": 456.5,
    "overhang_mm2": 15.9,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "holes_wrong_axis",
   "outcome_final": "holes_wrong_axis",
   "final_size_mm": "40 x 50 x 20",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "gear",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T11:21:34.910Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 5920,
    "extents": [
     22.0,
     22.0,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 286.8,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 1,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "22 x 22 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "gear",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T08:56:10.098Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 9040,
    "extents": [
     22.0,
     22.0,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 286.9,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "22 x 22 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": null,
   "part": "gear",
   "run": 3,
   "error": null,
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "empty_replies": 1,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": null,
   "part": "adapter",
   "run": 1,
   "error": null,
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 1,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "adapter",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:25:45.472Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 3200,
    "extents": [
     32.0,
     32.0,
     60.0
    ],
    "tube_sections": [
     {
      "z": 15.0,
      "outer": 32.0,
      "inner": 28.0
     },
     {
      "z": 45.0,
      "outer": 25.0,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 21.0,
     "25": 21.0
    },
    "transition_mm": 18.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9998299507228072
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.999829950722793
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.9998299507227912
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.9998299507228516
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9998299507228232
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9998299507228072
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9998299507228037
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.9998299507228197
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.999829950722802
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9998299507228108
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9998299507228108
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.9998299507228037
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9998299507227966
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9998299507228197
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9998299507227966
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.9998299507227895
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9998299507227841
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.999829950722793
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.999829950722802
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.9998299507228072
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.9998300508617977
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9998302525105842
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.99983045604621
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9998306615425108
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9998308690775044
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9998310787332496
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9998312905962834
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9998315047580242
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9998317213148074
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9998319403686384
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.9998321620272055
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9998323864047176
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9998326136219067
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.999832843806951
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.9998330770957633
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9998333136326245
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9998335535710456
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9998337970744
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9998340443163922
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9998342954825947
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.9998344225985516
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9998344225985143
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.9998344225985214
     },
     {
      "z": 43.5,
      "equivalent_wall_mm": 1.9998344225985338
     },
     {
      "z": 44.5,
      "equivalent_wall_mm": 1.9998344225985392
     },
     {
      "z": 45.5,
      "equivalent_wall_mm": 1.9998344225985427
     },
     {
      "z": 46.5,
      "equivalent_wall_mm": 1.9998344225985338
     },
     {
      "z": 47.5,
      "equivalent_wall_mm": 1.9998344225985285
     },
     {
      "z": 48.5,
      "equivalent_wall_mm": 1.9998344225985196
     },
     {
      "z": 49.5,
      "equivalent_wall_mm": 1.9998344225985178
     },
     {
      "z": 50.5,
      "equivalent_wall_mm": 1.999834422598525
     },
     {
      "z": 51.5,
      "equivalent_wall_mm": 1.999834422598516
     },
     {
      "z": 52.5,
      "equivalent_wall_mm": 1.9998344225985303
     },
     {
      "z": 53.5,
      "equivalent_wall_mm": 1.9998344225985214
     },
     {
      "z": 54.5,
      "equivalent_wall_mm": 1.9998344225985605
     },
     {
      "z": 55.5,
      "equivalent_wall_mm": 1.9998344225985196
     },
     {
      "z": 56.5,
      "equivalent_wall_mm": 1.9998344225985303
     },
     {
      "z": 57.5,
      "equivalent_wall_mm": 1.9998344225985267
     },
     {
      "z": 58.5,
      "equivalent_wall_mm": 1.9998344225985143
     },
     {
      "z": 59.5,
      "equivalent_wall_mm": 1.999834422598548
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 60",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "adapter",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:31:38.802Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1920,
    "extents": [
     32.0,
     32.0,
     50.0
    ],
    "tube_sections": [
     {
      "z": 12.5,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 37.5,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.5,
     "25": 20.5
    },
    "transition_mm": 9.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995411972022197
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.999541197202193
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.9995411972021877
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995411972021824
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995411972022161
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.999541197202186
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995411972022108
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999541197202225
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.9995414277974675
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9995419390078606
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.9995425202457735
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995431757823674
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.999543910221817
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995447285308607
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9995456360702004
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995466386283294
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995477424573593
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9995489543101677
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995496030020945
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995496030020625
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995496030020785
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 43.5,
      "equivalent_wall_mm": 1.9995496030020767
     },
     {
      "z": 44.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 45.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 46.5,
      "equivalent_wall_mm": 1.9995496030020732
     },
     {
      "z": 47.5,
      "equivalent_wall_mm": 1.9995496030020679
     },
     {
      "z": 48.5,
      "equivalent_wall_mm": 1.9995496030020536
     },
     {
      "z": 49.5,
      "equivalent_wall_mm": 1.9995496030020803
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 50",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "tag",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:32:37.563Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1308,
    "extents": [
     51.12,
     20.0,
     4.0
    ],
    "size_ok": false,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 1.9,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "out_of_bounds",
   "outcome_final": "out_of_bounds",
   "failure_note": "text size 11 centred at x = 32 runs 1.1 mm past the end",
   "final_size_mm": "51.12 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "tag",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:34:15.300Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1436,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "deepseek-v4-pro",
   "model_version": "deepseek-v4-pro",
   "part": "tag",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:35:42.209Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1800,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 984.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "box",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:36:04.293Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "box",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:41:45.795Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "box",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:42:12.397Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 156,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2396.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "plate",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:42:36.853Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1228,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.02,
       69.99
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3956.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "plate",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:43:04.517Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 988,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.02,
       69.99
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.8,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.8-flash",
   "part": "plate",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:47:12.082Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1308,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3956.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.8-flash",
   "part": "bracket",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:52:12.651Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1928,
    "extents": [
     50.0,
     20.0,
     40.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 968.2,
    "overhang_mm2": 17.5,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 20 x 40",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.6-flash",
   "part": "bracket",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T08:45:53.845Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1892,
    "extents": [
     50.0,
     40.0,
     20.0
    ],
    "size_ok": true,
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 544.0,
    "overhang_mm2": 28.9,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "50 x 40 x 20",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "bracket",
   "run": 3,
   "error": "fetch failed",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": "gemini-3.8-flash",
   "part": "gear",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:28:57.220Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 2256,
    "extents": [
     21.99,
     21.99,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 286.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "21.99 x 21.99 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "gear",
   "run": 2,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "gear",
   "run": 3,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "adapter",
   "run": 1,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "adapter",
   "run": 2,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "adapter",
   "run": 3,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "tag",
   "run": 1,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "tag",
   "run": 2,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemini",
   "model_version": null,
   "part": "tag",
   "run": 3,
   "error": "You exceeded your current quota, please check your plan and billing details. For more information on this error, head to: https://ai.google.dev/gemini-api/docs/rate-limits. To monitor your current usage, head to: https://ai.dev/rate-limit. \n* Quota exceeded for metric: generativelanguage.googleapis.",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "box",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T10:22:13.225Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 12,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 0,
      "holes_ok": false
     }
    ],
    "floor_ok": false,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "feature_missing",
   "outcome_final": "feature_missing",
   "failure_note": "A top-level solid cube unions with the hollow box, filling its cavity.",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "box",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T08:50:09.257Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "box",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T08:51:09.337Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "plate",
   "run": 1,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "plate",
   "run": 2,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "plate",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:03:38.858Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1052,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.01
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.7,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "bracket",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T10:37:20.170Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1056,
    "extents": [
     40.0,
     20.0,
     50.0
    ],
    "size_ok": true,
    "genus": 2,
    "through_holes_ok": false,
    "bed_contact_mm2": 768.2,
    "overhang_mm2": 47.7,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "feature_missing",
   "outcome_final": "feature_missing",
   "failure_note": "Measured genus is two, not the requested four through-holes. Code cuts holes only through the arm thickness even where the gusset adds material; no full bracket geometry validation is claimed.",
   "final_size_mm": "40 x 20 x 50",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 2,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "bracket",
   "run": 2,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "bracket",
   "run": 3,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "gear",
   "run": 1,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "gear",
   "run": 2,
   "error": null,
   "rendered": false,
   "fix_rendered": true,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:26:24.356Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "fixed": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 720,
    "extents": [
     22.0,
     22.0,
     6.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 3,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.0
      ],
      "diameter_ok": true,
      "teeth": 20,
      "teeth_ok": true
     }
    ],
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 257.9,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "render_error": "ERROR: The given mesh is not closed! Unable to convert to CGAL_Nef_Polyhedron.",
   "empty_replies": 0,
   "outcome_first": "not_closed",
   "outcome_final": "pass",
   "final_size_mm": "22 x 22 x 6",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": true
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "gear",
   "run": 3,
   "error": "Provider returned error",
   "rendered": false,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": "repair",
   "request_timestamp": "2026-10-27T09:29:43.701Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/gemma-4-31b/gear-3.scad, line 3",
   "empty_replies": 0,
   "outcome_first": "syntax_error",
   "outcome_final": "syntax_error",
   "failure_note": "Initial OpenSCAD parser error, followed by provider failure during repair. Initial reply must remain in the answered cohort.",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": true
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "adapter",
   "run": 1,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "adapter",
   "run": 2,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": null,
   "part": "adapter",
   "run": 3,
   "error": "Provider returned error",
   "rendered": null,
   "fix_rendered": null,
   "reply_saved": false,
   "initial_render_recorded": false,
   "repair_reply_saved": false,
   "error_stage": "initial",
   "request_timestamp": null,
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "empty_replies": 0,
   "outcome_first": "no_answer",
   "outcome_final": "no_answer",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "tag",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T09:52:15.260Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 596,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 0,
      "holes_ok": false
     }
    ],
    "raised_text": true,
    "genus": 0,
    "through_holes_ok": false,
    "bed_contact_mm2": 1000.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "feature_missing",
   "outcome_final": "feature_missing",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "tag",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T11:16:23.961Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 2,
    "non_manifold_edges": 0,
    "triangles": 264,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 0,
      "holes_ok": false
     }
    ],
    "raised_text": false,
    "through_holes_ok": false,
    "bed_contact_mm2": 1000.0,
    "overhang_mm2": 12.5,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "feature_missing",
   "outcome_final": "feature_missing",
   "failure_note": "Extra top-level solids fill the ring hole and raised-text relief, despite a later cleaned-up difference block.",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 2,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "gemma-4-31b",
   "model_version": "google/gemma-4-31b-it:free",
   "part": "tag",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-27T11:20:51.209Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 1176,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 0,
      "holes_ok": false
     }
    ],
    "raised_text": true,
    "genus": 0,
    "through_holes_ok": false,
    "bed_contact_mm2": 1000.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "feature_missing",
   "outcome_final": "feature_missing",
   "failure_note": "The top-level uncut plate unions with the later difference block and fills the ring hole.",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "box",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:08.486Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "box",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:21.782Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "box",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:30:49.115Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness away from sampled sections; corner shape"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 28,
    "extents": [
     60.0,
     40.0,
     25.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1,
      "holes": 0,
      "holes_ok": true
     },
     {
      "z": 12.5,
      "holes": 1,
      "holes_ok": true,
      "hole_size": [
       36.0,
       56.0
      ],
      "hole_size_ok": true
     }
    ],
    "floor_ok": true,
    "genus": 0,
    "through_holes_ok": true,
    "bed_contact_mm2": 2400.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "60 x 40 x 25",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "plate",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:31:00.477Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 588,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.39,
       3.39,
       3.39,
       3.39
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       70.02
      ],
      "pitch_ok": true
     }
    ],
    "genus": 0,
    "through_holes_ok": false,
    "bed_contact_mm2": 4000.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "blind_holes",
   "outcome_final": "blind_holes",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "plate",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:31:16.861Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 796,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.4,
       3.4,
       3.4,
       3.4
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.0,
       69.99
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.8,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "plate",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:31:36.873Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Hole centring relative to the plate; mechanical fit"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 604,
    "extents": [
     80.0,
     50.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 2,
      "holes": 4,
      "holes_ok": true,
      "hole_diameters": [
       3.39,
       3.39,
       3.39,
       3.39
      ],
      "diameter_ok": true,
      "hole_pitch": [
       40.04,
       69.99
      ],
      "pitch_ok": true
     }
    ],
    "genus": 4,
    "through_holes_ok": true,
    "bed_contact_mm2": 3963.9,
    "overhang_mm2": 0.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "80 x 50 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 4,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "bracket",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:32:27.500Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 464,
    "extents": [
     50.0,
     40.0,
     4.0
    ],
    "size_ok": false,
    "genus": 3,
    "through_holes_ok": false,
    "bed_contact_mm2": 1352.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "wrong_shape",
   "outcome_final": "wrong_shape",
   "final_size_mm": "50 x 40 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 3,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "bracket",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:36:22.110Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 708,
    "extents": [
     50.0,
     40.0,
     4.0
    ],
    "size_ok": false,
    "genus": 3,
    "through_holes_ok": false,
    "bed_contact_mm2": 1344.5,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "wrong_shape",
   "outcome_final": "wrong_shape",
   "final_size_mm": "50 x 40 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 3,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "bracket",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:36:57.055Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "4.5 mm hole diameters and placement on each arm",
    "Arm thickness, gusset shape and right angle",
    "Support-free printing"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 748,
    "extents": [
     50.0,
     40.0,
     4.0
    ],
    "size_ok": false,
    "genus": 3,
    "through_holes_ok": false,
    "bed_contact_mm2": 1652.4,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "wrong_shape",
   "outcome_final": "wrong_shape",
   "final_size_mm": "50 x 40 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 3,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "gear",
   "run": 1,
   "error": null,
   "rendered": false,
   "fix_rendered": false,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-27T08:46:49.821Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/nemotron-3-ultra/gear-1.scad, line 9",
   "fix_render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/nemotron-3-ultra/gear-1-fix.scad, line 24",
   "empty_replies": 0,
   "outcome_first": "syntax_error",
   "outcome_final": "syntax_error",
   "failure_note": "module = 1 as a parameter name, kept in the repair",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": true
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "gear",
   "run": 2,
   "error": null,
   "rendered": false,
   "fix_rendered": false,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:45:40.162Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/nemotron-3-ultra/gear-2.scad, line 276",
   "fix_render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/nemotron-3-ultra/gear-2-fix.scad, line 105",
   "empty_replies": 0,
   "outcome_first": "not_a_file",
   "outcome_final": "not_a_file",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": true
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "gear",
   "run": 3,
   "error": null,
   "rendered": false,
   "fix_rendered": false,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": true,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:49:38.617Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Involute tooth profile, pitch accuracy and meshing with another gear"
   ],
   "render_error": "ERROR: Parser error: syntax error in file tmp-gen/aicad/runs/nemotron-3-ultra/gear-3.scad, line 161",
   "fix_render_error": "ERROR: The given mesh is not closed! Unable to convert to CGAL_Nef_Polyhedron.",
   "empty_replies": 0,
   "outcome_first": "syntax_error",
   "outcome_final": "not_closed",
   "failure_note": "first version left the tooth construction as comments inside a call",
   "final_size_mm": null,
   "final_watertight": null,
   "final_shells": null,
   "final_through_holes": null,
   "repair_round": true
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "adapter",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:51:59.349Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 2400,
    "extents": [
     32.0,
     32.0,
     55.0
    ],
    "tube_sections": [
     {
      "z": 13.8,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 41.2,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.5,
     "25": 20.5
    },
    "transition_mm": 14.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995411972022143
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995411972021877
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.999541197202193
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.9995411972022161
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995411972022001
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995411972021948
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995411972021984
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995411972022108
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.9995411972021788
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995411972022126
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.999541197202218
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.999541197202209
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.9995411972021895
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.9995411972022161
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 2.02101292314204
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 2.0179448620939535
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 2.014876822425519
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 2.0118088048944394
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 2.0087408102891153
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 2.005672839429881
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 2.0026048931693516
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995369723938055
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9964690780231535
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9934012110117454
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.990333372348223
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9872655630554519
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.9841977841897354
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9811300368396765
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.978062322124325
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995496030020838
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995496030020679
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995496030020696
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995496030020856
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995496030020927
     },
     {
      "z": 40.5,
      "equivalent_wall_mm": 1.999549603002059
     },
     {
      "z": 41.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 42.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 43.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 44.5,
      "equivalent_wall_mm": 1.9995496030020732
     },
     {
      "z": 45.5,
      "equivalent_wall_mm": 1.9995496030020767
     },
     {
      "z": 46.5,
      "equivalent_wall_mm": 1.9995496030020696
     },
     {
      "z": 47.5,
      "equivalent_wall_mm": 1.9995496030020625
     },
     {
      "z": 48.5,
      "equivalent_wall_mm": 1.9995496030020803
     },
     {
      "z": 49.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 50.5,
      "equivalent_wall_mm": 1.9995496030020874
     },
     {
      "z": 51.5,
      "equivalent_wall_mm": 1.9995496030020767
     },
     {
      "z": 52.5,
      "equivalent_wall_mm": 1.9995496030020643
     },
     {
      "z": 53.5,
      "equivalent_wall_mm": 1.9995496030020625
     },
     {
      "z": 54.5,
      "equivalent_wall_mm": 1.9995496030020838
     }
    ],
    "open_through": true,
    "genus": 1,
    "through_holes_ok": true,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 4.0,
    "all_checks_pass": true
   },
   "empty_replies": 0,
   "outcome_first": "pass",
   "outcome_final": "pass",
   "final_size_mm": "32 x 32 x 55",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 1,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "adapter",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:52:30.905Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 2,
    "non_manifold_edges": 0,
    "triangles": 1920,
    "extents": [
     32.0,
     32.0,
     40.0
    ],
    "tube_sections": [
     {
      "z": 10.0,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 30.0,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.0,
     "25": 20.0
    },
    "transition_mm": 0.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995411972022197
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.999541197202193
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.9995411972021877
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995411972021824
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995411972022161
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.999541197202186
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995411972022108
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999541197202225
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995496030020945
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995496030020625
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9995496030020785
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995496030020767
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995496030020732
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995496030020679
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995496030020536
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995496030020803
     }
    ],
    "open_through": true,
    "through_holes_ok": false,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 144.4,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "disconnected",
   "outcome_final": "disconnected",
   "final_size_mm": "32 x 32 x 40",
   "final_watertight": true,
   "final_shells": 2,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "adapter",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:52:51.250Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Wall thickness between sampled heights and minimum local thickness of noncircular sections"
   ],
   "first": {
    "watertight": true,
    "bodies": 2,
    "non_manifold_edges": 0,
    "triangles": 1920,
    "extents": [
     32.0,
     32.0,
     40.0
    ],
    "tube_sections": [
     {
      "z": 10.0,
      "outer": 31.99,
      "inner": 27.99
     },
     {
      "z": 30.0,
      "outer": 24.99,
      "inner": 21.0
     }
    ],
    "diameters_ok": true,
    "wall_ok": true,
    "section_lengths": {
     "32": 20.0,
     "25": 20.0
    },
    "transition_mm": 0.0,
    "size_ok": true,
    "wall_samples": [
     {
      "z": 0.5,
      "equivalent_wall_mm": 1.9995411972022197
     },
     {
      "z": 1.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 2.5,
      "equivalent_wall_mm": 1.999541197202193
     },
     {
      "z": 3.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 4.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 5.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 6.5,
      "equivalent_wall_mm": 1.9995411972021966
     },
     {
      "z": 7.5,
      "equivalent_wall_mm": 1.9995411972021877
     },
     {
      "z": 8.5,
      "equivalent_wall_mm": 1.9995411972021824
     },
     {
      "z": 9.5,
      "equivalent_wall_mm": 1.9995411972022161
     },
     {
      "z": 10.5,
      "equivalent_wall_mm": 1.9995411972022055
     },
     {
      "z": 11.5,
      "equivalent_wall_mm": 1.999541197202186
     },
     {
      "z": 12.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 13.5,
      "equivalent_wall_mm": 1.9995411972022108
     },
     {
      "z": 14.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 15.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 16.5,
      "equivalent_wall_mm": 1.9995411972022072
     },
     {
      "z": 17.5,
      "equivalent_wall_mm": 1.999541197202202
     },
     {
      "z": 18.5,
      "equivalent_wall_mm": 1.9995411972022037
     },
     {
      "z": 19.5,
      "equivalent_wall_mm": 1.999541197202225
     },
     {
      "z": 20.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 21.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 22.5,
      "equivalent_wall_mm": 1.9995496030020714
     },
     {
      "z": 23.5,
      "equivalent_wall_mm": 1.9995496030020945
     },
     {
      "z": 24.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 25.5,
      "equivalent_wall_mm": 1.9995496030020625
     },
     {
      "z": 26.5,
      "equivalent_wall_mm": 1.9995496030020785
     },
     {
      "z": 27.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 28.5,
      "equivalent_wall_mm": 1.9995496030020607
     },
     {
      "z": 29.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 30.5,
      "equivalent_wall_mm": 1.999549603002075
     },
     {
      "z": 31.5,
      "equivalent_wall_mm": 1.9995496030020572
     },
     {
      "z": 32.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 33.5,
      "equivalent_wall_mm": 1.9995496030020767
     },
     {
      "z": 34.5,
      "equivalent_wall_mm": 1.999549603002066
     },
     {
      "z": 35.5,
      "equivalent_wall_mm": 1.9995496030020892
     },
     {
      "z": 36.5,
      "equivalent_wall_mm": 1.9995496030020732
     },
     {
      "z": 37.5,
      "equivalent_wall_mm": 1.9995496030020679
     },
     {
      "z": 38.5,
      "equivalent_wall_mm": 1.9995496030020536
     },
     {
      "z": 39.5,
      "equivalent_wall_mm": 1.9995496030020803
     }
    ],
    "open_through": true,
    "through_holes_ok": false,
    "bed_contact_mm2": 188.4,
    "overhang_mm2": 144.4,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "disconnected",
   "outcome_final": "disconnected",
   "final_size_mm": "32 x 32 x 40",
   "final_watertight": true,
   "final_shells": 2,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "tag",
   "run": 1,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:53:19.957Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 5,
    "non_manifold_edges": 0,
    "triangles": 1306,
    "extents": [
     50.0,
     20.0,
     4.5
    ],
    "size_ok": false,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       4.0
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "through_holes_ok": false,
    "bed_contact_mm2": 987.5,
    "overhang_mm2": 91.9,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "disconnected",
   "outcome_final": "disconnected",
   "final_size_mm": "50 x 20 x 4.5",
   "final_watertight": true,
   "final_shells": 5,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "tag",
   "run": 2,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:53:51.065Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 5,
    "non_manifold_edges": 0,
    "triangles": 788,
    "extents": [
     50.0,
     20.0,
     4.5
    ],
    "size_ok": false,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       5.05
      ],
      "diameter_ok": false
     }
    ],
    "raised_text": true,
    "through_holes_ok": false,
    "bed_contact_mm2": 986.3,
    "overhang_mm2": 71.7,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "disconnected",
   "outcome_final": "disconnected",
   "final_size_mm": "50 x 20 x 4.5",
   "final_watertight": true,
   "final_shells": 5,
   "final_through_holes": null,
   "repair_round": false
  },
  {
   "model": "nemotron-3-ultra",
   "model_version": "nvidia/nemotron-3-ultra-550b-a55b:free",
   "part": "tag",
   "run": 3,
   "error": null,
   "rendered": true,
   "fix_rendered": null,
   "reply_saved": true,
   "initial_render_recorded": true,
   "repair_reply_saved": false,
   "error_stage": null,
   "request_timestamp": "2026-10-22T10:54:07.175Z",
   "repair_model_version": null,
   "unchecked_requirements": [
    "Literal TEST text and font shape",
    "Independent plate and raised-text thicknesses",
    "Hole placement near an end"
   ],
   "first": {
    "watertight": true,
    "bodies": 1,
    "non_manifold_edges": 0,
    "triangles": 724,
    "extents": [
     50.0,
     20.0,
     4.0
    ],
    "size_ok": true,
    "sections": [
     {
      "z": 1.5,
      "holes": 1,
      "holes_ok": true,
      "hole_diameters": [
       3.99
      ],
      "diameter_ok": true
     }
    ],
    "raised_text": true,
    "genus": 0,
    "through_holes_ok": false,
    "bed_contact_mm2": 1000.0,
    "overhang_mm2": 0.0,
    "all_checks_pass": false
   },
   "empty_replies": 0,
   "outcome_first": "blind_holes",
   "outcome_final": "blind_holes",
   "final_size_mm": "50 x 20 x 4",
   "final_watertight": true,
   "final_shells": 1,
   "final_through_holes": 0,
   "repair_round": false
  }
 ]
}
